Search results for "Thermoelastic damping"
showing 10 items of 25 documents
Melting temperature prediction by thermoelastic instability: An ab initio modelling, for periclase (MgO)
2021
Abstract Melting temperature (TM) is a crucial physical property of solids and plays an important role for the characterization of materials, allowing us to understand their behavior at non-ambient conditions. The present investigation aims i) to provide a physically sound basis to the estimation of TM through a “critical temperature” (TC), which signals the onset of thermodynamic instability due to a change of the isothermal bulk modulus from positive to negative at a given PC-VC-TC point, such that (∂P/∂V)VC,TC = -(∂2F/∂V2) VC,TC = 0; ii) to discuss the case of periclase (MgO), for which accurate melting temperature observations as a function of pressure are available. Using first princip…
A bending theory of thermoelastic diffusion plates based on Green-Naghdi theory
2017
Abstract This article is concerned with bending plate theory for thermoelastic diffusion materials under Green-Naghdi theory. First, we present the basic equations which characterize the bending of thin thermoelastic diffusion plates for type II and III models. The theory allows for the effect of transverse shear deformation without any shear correction factor, and permits the propagation of waves at a finite speed without energy dissipation for type II model and with energy dissipation for type III model. By the semigroup theory of linear operators, we prove the well-posedness of the both models and the asymptotic behavior of the solutions of type III model. For unbounded plate of type III…
The development of a hybrid technique employing the boundary element method for thermoelastic stress separation
2000
: This paper presents a development of a hybrid technique employing a boundary element method for determining individual stress components in two-dimensional arbitrarily shaped domains from experimental isopachics only. The procedure consists of a numerical solution of two Poisson equations representing equilibrium for two-dimensional plane-stressed solids with zero body forces. An existing technique is employed for smoothing interior thermoelastic data and enhancing boundary information. The algorithm of stress separation has been implemented with the help of commercial codes. The whole procedure has been tested through a complete post-processing example of thermoelastic stress analysis da…
Anomalous thermoelastic behavior of (KI)1-x(NH4I)x
1990
Abstract An anomalous softening of the shear mode c 44 is observed in (KI) 1- x (NH 4 I) x with Brillouin scattering (10 K ⩽ T ⩽ 300 K ). It is caused by the weak quadrupolar moment of the NH 4 + ion, induced by the C 3 v symmetry of the potential. A parallel decrease of the lifetime of this transverse phonon at lower temperatures is observed. Static random strain fields due to admixing KI with NH 4 I are small. The results have been treated in terms of a mean field theory. The c 11 elastic constant does not show any anomalous behavior. Also are given the elastic constants c 11 and c 44 for x =0.14, 0.43 and 1 and 1 at T = 300 K and 10 K .
Thermoelastic stress analysis of a 2D stress field using a single detector infrared scanner and lock-in filtering
2009
A low resolution, low cost, fast infrared scanner is used to acquire the temperature change along a line on the surface of cyclically loaded samples. The temperature signal is sampled versus time by exploiting the raster scanning movement of the thermocamera single detector. The temperature data is then post-processed by a Fast Fourier Transform based lock- in algorithm implemented in MATLAB ® , in order to filter out the thermoelastic effect induced temperature change. A procedure is also implemented in order to extend the data sampling time by opportunely synchronising successively grabbed data frames. The effectiveness of such synchronisation procedure is first demonstrated by performing…
On relation between J-integral and heat energy dissipation at the crack tip in stainless steel specimens
2019
In this paper, an experimental procedure to evaluate the elastic-plastic J-integral at the tip of a fatigue crack is presented. According to this new approach, the elastic component of the J-integral is derived from Thermoelastic Stress Analysis, while the plastic component of the J-integral is derived from the heat energy loss. An analytical link is proposed to apply this new experimental technique. Therefore, the elastic-plastic J-integral range was evaluated starting from infrared temperature maps measured in situ during crack propagation tests of AISI 304L stainless steel specimens. It was found that the range of the infrared thermography-based J-integral correlated well the crack growt…
Simultaneous laser generation and laser ultrasonic detection of the mechanical breakdown of a coating–substrate interface
2001
Abstract The present study deals with information that could be obtained by real-time contactless monitoring of the normal displacement, due to the propagation of the longitudinal waves generated by nanosecond pulsed laser irradiation, through a transparent and porous ceramic coating deposited on a metallic substrate. These displacements were recorded in real-time at the rear surface of the specimens using a laser heterodyne interferometer and were correlated with the different steps of laser/material interaction (thermoelastic interactions, fracture of the coating–substrate interface and coating expulsion). An analytical model was developed to establish a relation between the longitudinal …
Infrared Thermography assisted evaluation of static and fatigue Mode II fracture toughness in FRP composites
2019
Abstract The work proposes the combined use of a Modified Transverse Crack Tension (MTCT) test coupon and Infrared Thermography, to evaluate the static and fatigue behaviour of Fibre Reinforced Polymer composites under Mode II delamination. Artificial delaminations starters are added to the TCT coupon, whose effects on the Strain Energy Release Rate are discussed. Infrared Thermography and Thermoelastic Stress Analysis are implemented to investigate stresses and delaminations growths on two FRP materials: a pre-preg IM7/8552 carbon fibre-epoxy and a glass-fibre reinforced epoxy laminates. The thermographic, thermoelastic and second harmonic signals have been obtained and used to monitor the…
Thermoelastic Stress Analysis of modified Transverse Cut Tensile composite specimens under pure Mode II fatigue delamination
2018
The present work investigates the behaviour of a Transvers Crack Tensile (TCT) specimen undergoing fatigue loading, by means of a Thermoelastic Stress Analysis (TSA) experimental setup. The TCT is a tensile composite specimen where a number of internal layers are cut through the beam width. The presence of such transverse notch favours the formation of interlaminar Mode II delaminations, starting from the notch tips and propagating between the cut and continuous plies. In this work, a modification is adopted to the classic TCT specimen, where insert films, mimicking artificial delaminations, are laid across the notch tips. This is done with the purpose to favour a pure Mode II and a symmetr…
Quantification of Plasma Sprayed Coating Adhesion Using Pulsed Laser Induced Decohesion Technique
2001
Abstract The aim of the present study is to compare a laser ultrasonic technique with a conventional indentation test for the determination of intrinsic properties and the adhesion of alumina coatings, of different thicknesses (30–350 µm), deposited on stainless steel substrates by atmospheric plasma spraying (APS). For this purpose, a pulsed Nd:YAG laser is used to irradiate the coated specimens, and the ultrasonic waves generated by the laser are recorded at the epicenter using a laser interferometer. In the thermoelastic regime, the good agreement between the experiment and computation allows determination of the longitudinal wave velocity as well as the Young's modulus of the oxide coat…